If all of the above items are ok then there is a possibility that your Dyson V10 battery<\/a> has failed and will need to be replaced. Don’t worry this is an easy procedure to change out the battery for a new one. These aftermarket batteries will let you use the vacuum for longer as they are of higher capacity than stock.<\/p>\n\n\n\n The stock battery has a life span of many years if used every day. This is a design of the internal Lithium-ion battery as they can handle up to around 600 charge cycles before they begin to lose capacity slowly. In fact, James Dyson, who founded the company back in 1987, said that battery life won\u2019t be an issue for the Cyclone V10.\u00a0\u201cFifteen years of daily use might get you down to 80% battery,\u201d\u00a0(let’s see if that is true)<\/em><\/p>\n\n\n\n As the Dyson V10 has been around for a few years now if you are noticing that your V10 is not lasting the full 50-60 minutes you will require a new battery.<\/p>\n\n\n\n If your Dyson V10 has solid blue lights but not power then you will often have a jam in either the rotating powerhead or a faulty battery.<\/p>\n\n\n\n The rotating powerheads are designed to stop if it detects a high current draw due to a blockage or tangle. This saves the motor and associated gears from breaking due to a high torque load.<\/p>\n\n\n\n Not only will the powerhead stop, but often the main motor for the vacuum cleaner will stop as well.<\/p>\n\n\n\n If you have no blockage tangles or foreign objects in the powerhead then you could have a faulty battery. The solution, replace the V10 battery.<\/p>\n\n\n\n Dyson V10 cordless vacuum cleaners don’t have a reset button. But there are a few tricks you can do to clear any internal electrical faults you may have.<\/p>\n\n\n\n Most faults are caused by either a blockage in the rotating brush head or one of the covers is not attached properly. Make sure all of the covers are clicked into position and there are no blockages.<\/p>\n\n\n\n Remove the center brush bar by using a coin to turn the holding screw anticlockwise. You can then pull out the brush-bar. Remove and string, hair, rope, and dust that may be jamming the brush bar. Once it is clean and free you can replace it back and tighten the lock nut. <\/p>\n\n\n\n Try removing the Dyson V10 from the charger and turning off the charger from the wall for around 1 minute. Then turn it on again and place the V10 into the charger while pressing the trigger button for 30 seconds. Nothing will happen but it should reset any faults that are preventing your Dyson from charging and running.<\/p>\n\n\n\n You can also try removing the Dyson V10 battery and pressing the trigger for 30 seconds. Place the battery back into the cordless vacuum and recharge it for a few hours.<\/p>\n\n\n\n Dyson makes it really easy to replace the filter on the V10. Just turn the rear blue cap anti-clockwise 1\/5 turn until it screws off and remove the mesh filter. Replacement mesh filters are cheap and you can buy a pack of three filters for the V10 here<\/a>.<\/p>\n\n\n\n I like to replace this Hepa filter every year but if you have access to some high-pressure air you can blow out the excess dust. Make sure to use eye protection with high-pressure air.<\/em><\/p>\n\n\n\n Some people rinse them out under clean running water but you have to make sure they are completely dry before use. If the filter is not dry you will clog up the filter and your Dyson v10 will be pulsing after cleaning the filter.<\/p>\n\n\n\n The problem is that if the filter is not secured properly then the limit switch on the Dyson v10 won’t activate and it won’t startup.<\/p>\n\n\n\n If your Dyson V10 is not working after cleaning or replacing the filter then it could be a limit switch error. The problem 99 times out of 100 is because the rear HEPA filter is not screwed on correctly.<\/p>\n\n\n\n Remove the filter and clean out any dust and dirt that may be trapped between the threads of the blue filter. Replace the filter and screw it on. There should be no gap between the grey body of the cordless vacuum and the blue filter.<\/p>\n\n\n\n If your Dyson V10 is pulsing after replacing the filter then check for blockages, tangles in the brush head, or a wet filter. These problems can cause the vacuum cleaner to pulse during operation because of extra power draw.<\/p>\n\n\n\nDyson v10 3 solid blue lights no power fix.<\/h2>\n\n\n
![\"Dyson](\"https:\/\/notsealed.com\/wp-content\/uploads\/2021\/06\/Dyson-V10-3-solid-blue-lights-no-power.jpg\")
<\/figure><\/div>\n\n\nHow do I reset my Dyson V10?<\/h2>\n\n\n\n
Dyson v10 filter replacement<\/h2>\n\n\n
![\"Dyson](\"https:\/\/notsealed.com\/wp-content\/uploads\/2021\/06\/Dyson-v10-filter-removal.jpg\")
<\/figure><\/div>\n\n\nDyson v10 not working after cleaning filter repair.<\/h3>\n\n\n\n